GFK4B Fireplace Blower Fan Kit for Heatilator NDV4236, NDV4236I Fireplace
- In Stock. Ships to Canada USPS. Free UPS shipping to 48 States. Normally ships by Next Business Day.
Our GFK4B Fireplace Blower Fan Kit is designed for the Heatilator NDV4236, NDV4236I gas fireplace insert to circulate air around the firebox and enhance heat output. This complete fireplace blower kit offers a low cost solution to push heat created by the fireplace into your living space.
A speed control module with timer circuit is included with the blower kit which automatically turns the fan ON / OFF at preset times and is equipped with a Speed Button to provide a quiet airflow at the desired speeds. The timer circuit will delay fan operation; by automatically turning ON the fan 7 minutes after the main flame has been turned ON (After the fireplace has warmed up) and turning the fan OFF 12 minutes after the main flame has been turned OFF (After the fireplace has cooled down).
Fireplace Blower Kit Includes
- Speed Control Module with Timer Circuit by Skytech
- Jumper and Ground Wires
- Hardware and Adhesive Velcro Strips/Dampening Pad - (Easy to install plus reduces Vibration)
- Installation Instructions
- 1 Year Comprehensive Warranty on Blower
- 2 Year Warranty on Control Module
- Dimensions in Inches: W: 12.94 x H: 3.6 x D: 4.27
- Motor is equipped with Thermal Safety Switch
- Bearing Construction Type: Ball Bearings
- CFM: 135
- AMPS: 0.74
- HZ: 60
- Volts: 115
- RPM: 3000 (1/1400 with load)
- Rotation: CW
- Blower Wheel Dimensions: Width: 9.45in (240mm) Diameter: 2.56in (65mm)
- Anti-Vibration Impellers & Vortex Regulation Tabs to provide a steady airflow
- This fireplace blower fan produces high airflow and is manufactured with quality parts and components
- Increase Heating Potential of your gas fireplace insert with this hgih airflow blower fan
- Simple wiring connections makes installation Quick and Easy
If you have had any custom work done to your gas fireplace insert, compare the dimensions listed with the clearance in your appliance to insure proper fit.
This fireplace blower fan kit was Assembled & Tested in the Midwest which includes parts Manufactured in the USA. Industry Research & Design contributed to the manufacturing of this high quality aftermarket fireplace blower kit and is designed to meet the original equipment specifications. The instruction manual provided may not include specific information about your exact fireplace model, though we try to provide technical support in assisting you.
Videos Hide Videos Show Videos
Ordered over phone with assistance from Rep. Received product, installed (super easy), works great!
We are very pleased with this blower. A little tricky to install in a previously installed fireplace, but the blower has various speeds and allows you to adjust as needed.
Received and installed per very good installation instructions. All parts seem to be of high quality and the product works very well. Puts out volume of air similar to a floor A/C and heating vent.
Does throw out some good heat, but is a little noisy
Figured out the instructions eventually. Great product and good customer service.
I would recommend laying out all the pieces and reading through the directions before actually installing the fan. I just jumped right in and had some confusion on what wire was what. At any rate, I did maneuver the fan into place as a test which was recommended in other reviews. That definitely helped. The entire process took just under 30 minutes, so it is not too difficult. Medium-Low is the fan speed to go with as the higher two speeds are too loud. Will be fine as medium-low still pushes a good amount of air out into the room which is all I was wanting. If I lose power I'll switch the speed to high to help heat the house in the winter. Great product, good instructions, happy customer.
Everything arrived in good condition. The fan was larger than expected (good) but was a little challenging to fit into the space .(apparently they all are). Works fine, I don't mind the blower running on full even though it is not super quiet.
We have had the blower now for a few weeks and are very pleased. It was a little difficult to install after the fact but I managed to maneuver it to the back. We decided to put the fan on med because high seemed to loud. Other than that very happy with the product
Works great to distribute heat from firebox. Installation was easy. Just followed the written directions. Most challenging part was maneuvering the blower/fan to the back of the box.
I've been looking to purchase this for a while. My hesitation was the install. Out of curiosity I called for a quote to have someone come install one. They wanted $600. This was the final deciding factor to buy it my self.
I watched videos and worried the small area would be very difficult to install this fan. I measured it out and it seemed to fit. I then ordered it.
Install was fairly easy, they provide a couple wires for several types so that was sorta confusing. I followed the directions and as expected it works perfect.