GFK4B Fireplace Blower Fan Kit for Heatilator ND4236, ND4236I, Fireplace
- In Stock. Ships to Canada USPS. Free UPS shipping to 48 States. Normally ships by Next Business Day.
Our GFK4B Fireplace Blower Fan Kit is designed for the Heatilator ND4236, ND4236I, gas fireplace insert to circulate air around the firebox and enhance heat output. This complete fireplace blower kit offers a low cost solution to push heat created by the fireplace into your living space.
A speed control module with timer circuit is included with the blower kit which automatically turns the fan ON / OFF at preset times and is equipped with a Speed Button to provide a quiet airflow at the desired speeds. The timer circuit will delay fan operation; by automatically turning ON the fan 7 minutes after the main flame has been turned ON (After the fireplace has warmed up) and turning the fan OFF 12 minutes after the main flame has been turned OFF (After the fireplace has cooled down).
Fireplace Blower Kit Includes
- Speed Control Module with Timer Circuit by Skytech
- Jumper and Ground Wires
- Hardware and Adhesive Velcro Strips/Dampening Pad - (Easy to install plus reduces Vibration)
- Installation Instructions
- 1 Year Comprehensive Warranty on Blower
- 2 Year Warranty on Control Module
- Dimensions in Inches: W: 12.94 x H: 3.6 x D: 4.27
- Motor is equipped with Thermal Safety Switch
- Bearing Construction Type: Ball Bearings
- CFM: 135
- AMPS: 0.74
- HZ: 60
- Volts: 115
- RPM: 3000 (1/1400 with load)
- Rotation: CW
- Blower Wheel Dimensions: Width: 9.45in (240mm) Diameter: 2.56in (65mm)
- Anti-Vibration Impellers & Vortex Regulation Tabs to provide a steady airflow
- This fireplace blower fan produces high airflow and is manufactured with quality parts and components
- Increase Heating Potential of your gas fireplace insert with this hgih airflow blower fan
- Simple wiring connections makes installation Quick and Easy
If you have had any custom work done to your gas fireplace insert, compare the dimensions listed with the clearance in your appliance to insure proper fit.
This fireplace blower fan kit was Assembled & Tested in the Midwest which includes parts Manufactured in the USA. Industry Research & Design contributed to the manufacturing of this high quality aftermarket fireplace blower kit and is designed to meet the original equipment specifications. The instruction manual provided may not include specific information about your exact fireplace model, though we try to provide technical support in assisting you.
Videos Hide Videos Show Videos
Fairly easy install and it warms up my family room.
Looked around and read reviews for various models. This ll”looked” to be a much better quality fan than the others. It was a little bit more expensive but well worth the few extra dollars. Easy to install and instructions were pretty good and not difficult to follow. I would highly recommend this fan.
It was a lot harder to install than other reviewers had said but the people at My Fireplace Blower provided excellent technical support and were just wonderful to work with. Once my friend finally got the blower installed, it works great.
The fan kit was pretty easy to install. My gas connection was on the left side with the fireplace controller electronics module on the right. There would have been a little more room to maneuver the fan unit on the left, but I didn't want to disconnect the gas supply if I didn't have to. After moving the existing wiring to the sides, I was able to get the fan unit into the fireplace with a slow, methodical, turning and turning the fan unit as I slowly guided past obstructions. Once it was in place, the wiring was straight forward and simple based on the instructions that came with the unit. Perhaps I was lucky, but my Heatilator fireplace had a small pre-drilled hole in the metal bottom near each front corner where the two ground wires from the fan kit could be easily screwed into place.connect .
The fan works very well, although the fan noise is a bit more than I like at it two highest settings, so I just run it in the second lowest speed, which seems to be adequate for the where I live. At least I know there is some reserve capacity if it got really cold and I want more room heating.
I'm very pleased with the quality and performance of this fan kit.
Product works exactly as described. Installation was straight forward as detailed instructions were provided with the product. Wish I would have purchased one of these sooner.
SO FAR SO GOOD. CAN TURN THERMOSTAT DOWN AT LEAST 5 DEGREES AND BLOWER DOES THE REST.
TOASTY WARM ON THESE COLD DAYS.
Easy install. Louder than expected but has multiple speed settings so I slowed it down to reduce the noise. I have heard from others these don’t last long and get louder and squeaky after a while. Time will tell so can’t give it 4 stars yet.
I went with this brand because it had the exact model of my gas fireplace, they had installation videos and included EVERYTHING needed to get the job done. I had this finished in less then an hour. That includes cleaning out the dust and carefully reading the instructions!
I recently installed the GFK4B fan kit on our gas fireplace. It now allows me to get more heat into the room instead of sending it all out the chimney. It is a quick and easy installation and works as advertised. The only negative feedback I can give is I feel the fan is a little noisy It it was quieter I would have given it 5 stars
Fireplace blower was as advertised, excellent installation instructions, good fit, great performance so far (one week).